ELC-LT2402 Years Warranty
Step3-2Intel*LGA775ENDEFRITESPLTNCNIDJPKRRUNoce: For LGA775, please place the square spacer on the central hole of the back plate.Bie beachten Sie:
Step4-1IntelENDEFRITESPLTNCNIDJPKRRUInstall the Intel back plate on to the back of motherboard; fix the back plate with the stand-offBefesgen Sie die I
Step4-2IntelENDEFRITESPLTNCNIDJPKRRU*LGA2011Tighten the Intel LGA 2011 screw to the motherboard Schrauben Sie die Backplate mit den passenden LGA2011-
ENDEFRITESPLTNCNIDJPKRRUApply the thermal grease evenly on the CPU surfaceVerteilen Sie gleichmäßig eine dünne Schicht Wärmeleitpaste auf der CPU-Ober
ENDEFRITESPLTNCNIDJPKRRURemove the protect film from the cold-plateEnernen Sie die Schutzfolie von der Kühlplae der Pumpe.Rerez le film protecteur de
ENDEFRITESPLTNCNIDJPKRRUStep7IntelPlace the pump on the CPU and ghten the spring screws unl all four corners are securedPlatzieren Sie die Pumpe auf
ENDEFRITESPLTNCNIDJPKRRUPump4 pinPump3 pin orStep8IntelConnect the pump power connector to the motherboardSchließen Sie den Stromstecker der Pumpe am
ENDEFRITESPLTNCNIDJPKRRUPWM Y cable4 pin1st fan 2st fanStep9IntelConnect the fan connector to the motherboardSchließen Sie den 4-Pin-PWM-Stecker des L
- 16 -AMD Installation
Step1AMDENDEFRITESPLTNCNIDJPKRRUChoose your desired max. fan speed by adjusng the speed control at the fan hub.Wählen Sie die gewünschte Maximaldrehz
Limited Warranty SpecificaonPart listIntel InstallaonAMD Installaon123416Index
ENDEFRITESPLTNCNIDJPKRRUAach the fan and the radiator to the chassisSchrauben Sie den Lüer und den Radiator am Gehäuse fest.Fixez le venlateur et l
ENDEFRITESPLTNCNIDJPKRRUStep3AMDRemove the preinstalled Intel clip and install the AMD clip to the pumpEnernen Sie die vorinstallierten Halterungen f
ENDEFRITESPLTNCNIDJPKRRUStep4-1AMDSck the insulang sheet on the appropriate posion.Legen Sie die Entkopplungsplaen an die vorgesehenen Stellen auf
*AligningStep4-2AMDENDEFRITESPLTNCNIDJPKRRUPlace the square spacer on the central hole of the back plate. Insert the posion screw into the appropria
ENDEFRITESPLTNCNIDJPKRRUStep5AMDInstall the AMD back plate on to the back of motherboard; fix the back plate with the stand-offBefesgen Sie die AMD-Bac
ENDEFRITESPLTNCNIDJPKRRUApply the thermal grease evenly on the CPU surfaceVerteilen Sie gleichmäßig eine dünne Schicht Wärmeleitpaste auf der CPU-Ober
ENDEFRITESPLTNCNIDJPKRRURemove the protect film from the cold-plateEnernen Sie die Schutzfolie von der Kühlplae der Pumpe.Rerez le film protecteur de
ENDEFRITESPLTNCNIDJPKRRUPlace the pump on the CPU and ghten the spring screws unl all four corners are securedPlatzieren Sie die Pumpe auf der CPU u
Step9AMDENDEFRITESPLTNCNIDJPKRRUPump4 pinPump3 pin orConnect the pump power connector to the motherboardSchließen Sie den Stromstecker der Pumpe am Ma
PWM Y cable4 pin1st fan 2st fanENDEFRITESPLTNCNIDJPKRRUConnect the fan connector to the motherboardSchließen Sie den 4-Pin-PWM-Stecker des Lüers am M
Limited WarrantyPlease read this limited warranty carefully. Warranty is subject to void under following criteria:1. The serial number label or warran
© 2013 Enermax Technology Corporation. All rights reserved. Technical changes, printing errors and mistakes excepted.
PumpSpecificaonModelCold PlateRadiatorTubeELC-LT240-HPWeight (w/o fan)BracketIntel® LGA 775/1150/1155/1156/1366/2011AMD® AM2/AM2+/AM3/AM3+/FM1/FM2/FM2
Part listA Cooler x 1 B Fan x 2 C Back Plate x 1 D Square Spacer x 1E Stand-off x 4F Fan Screw x 8G Case Screw x 8M Insulang sheet x 4
Intel Installation- 4 -
ENDEFRITESPLTNCNIDJPKRRUChoose your desired max. fan speed by adjusng the speed control at the fan hub.Wählen Sie die gewünschte Maximaldrehzahl des
ENDEFRITESPLTNCNIDJPKRRUAach the fan and the radiator to the chassisSchrauben Sie den Lüer und den Radiator am Gehäuse fest.Fixez le venlateur et l
ENDEFRITESPLTNCNIDJPKRRU*AligningLGA1366LGA775LGA1150/1155/1156Step3-1Intel*LGA775/1150/1155/1156/1366Insert the posion screw into the appropriate ho
Comments to this Manuals